Ice maker hookup instructions, tapping the cold water line

Drill as close to the back wall of the cabinet as possible, he dating another woman so you do not lose storage space inside the cabinet. Place a level on top of the cabinet. Wrap the female thread on the opposite end of the adapter with thread-seal tape.

Page Troubleshooting Troubleshooting Operational notes i. The ice bucket will be sitting on top of the freezer shelf. Find your water supply lines beneath your sink.

How to Hook Up a Water Line to a Refrigerator From the Sink

Ice maker hookup instructions

How to Install a Water Line for a Refrigerator Ice Maker

WHIRLPOOL ECKMF94 - AUTOMATIC ICE MAKER INSTALLATION MANUAL Pdf Download

Ice maker hookup instructions
Ice maker hookup instructions
How to Hook Up a Water Line to a Refrigerator From the Sink

If this happens, you will have to cut off the end of the tubing, purchase a new compression sleeve, and start over. She writes mainly home improvement, kenya whatsapp dating groups health and travel articles for various online publications. Tighten the connections slightly if you see a leak. Carefully slide the pilot tube of the shut-off clamp with the threaded hole in the center valve into the water pipe access hole so it from the copper tubing kit.

Wash out the ice bucket, and then slide it under the ice maker see the side diagram as far as it will go. Position the ice maker inside the freezer compartment and connect its wiring con- nector to the wiring harness connector so they lock together the locking arm will snap over the raised tab. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink. Follow the instructions carefully.

Turn the cold water supply valve on beneath the sink. Untape the coiled flexible tubing coming from the water valve and straighten it. Coil the excess water line behind the refrigerator. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction.

Tapping the Cold Water Line

Ice maker hookup instructions
  1. These conditions can cause serious personal injury if the suggested procedures are not observed.
  2. Page Connecting The Copper Tubing Connecting the copper tubing to the water valve Refer to the diagram below for the following steps.
  3. Insert the new water line into the opening on the tee.
  4. Insert the end of the tubing into the water the tubing is round and cut even.

Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. Thread the ferrule from the kit onto the new line. Uncoil the necessary length of copper tubing and straighten it, then route the end of the tubing through the access hole you drilled to the location you have chosen to install the shut-off valve.

Home Guides

Whirlpool ECKMF94 - Automatic Ice Maker Installation Manual

Whirlpool ECKMF94 - Automatic Ice Maker Installation Manual

Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench.

You will be working inside the freezer compartment. Push the refrigerator against the wall. Regular screwdriver stand it before you perform it. Page Installing The Shut-off Valve Installing the shut-off valve Refer to the diagram below for the following steps. Watch for leaks at all the connections.

How to Install a Water Line for a Refrigerator Ice Maker

You are being redirected

How to Hook Up a Water Line to a Refrigerator From the Sink

Check all of the components in the kit against the following list to help you become familiar with them. Turn the cold water on the supply line clockwise to close it. Slip the remaining compression nut and ferrule over the refrigerator end of the new water line.

The valve connected to the right side of the faucet is the cold water supply line. Read You will need these tools to install your kit. Do not twist the nuts too tight as this could damage the supply valve, james maslow dating list the supply line and the adapter. The kit provides you with the required parts to hook up a water line to your refrigerator. Connect the line to the water line connector on the back of the refrigerator.

Twist the faucet supply line onto the female end of the adapter. Twist the male end of a quick-tee adapter onto the valve. She attended Tarrant County College and studied English composition. Leave the excess water line behind the refrigerator. Page To The Shut-off Valve Connecting the copper tubing to the shut-off valve Refer to the diagram below for the following steps.

Ice maker hookup instructions
Ice maker hookup instructions
  • Turn on the cold water faucet to drain any water left in the supply line.
  • Turn the supply line on once again.
  • You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink.
  • Slip the compression nut that came with the kit over the newly installed supply line.
  • Both of these control the water flow.

The connectors will fit together only one way. Use pliers to untwist the faucet supply line from the cold water supply valve. Optional parts are not included in this list. Plug your refrigerator into the wall.

  • Miss dating you quotes
  • Dating asian american guys
  • Hiv positive dating sites in sa
  • Adventure dating app
  • Online dating introduction template
  • Important things to know about someone you're dating
  • Expat speed dating amsterdam
  • Guy ignores me after hook up
  • Casual sex dating free